
Topping
Refine Search
- APX555B limited our measurement again
- 4PIN XLR+4.4mm+6.35mm output
- SE + BAL input pass through
RM1,169.00
RM1,399.00
- Product type: HiFi rack
- Material: Aluminium and acrylic
- Colors: Transparent and silver
- Dimensions: 15.8 x 17.2 x 11.2cm
RM149.00
- Bluetooth 5.0 Trasmission
- Auto Screen Close
- Easy to Operate
- Tablet and Phone Application
RM1,399.00
RM1,599.00
- Support Highest DSD512(Native) and PCM 32Bit/768kHz
- Bluetooth 5.0 LDAC transmission
- 2*ESS ES9038Q2M SABRE HIFI DAC
- THD+N as low as 0.00025%
- XMOS XU208 and customized drivers
- Auto on/off& Auto screen close
- USB/Coaxial/Optical DAC application
- DAC+Pre-amplifier/ Bluetooth receiver/Tablet and phone DAC application
RM899.00
- 5V power supply, anytime and anywhere
- DAC filter mode
- Auto turn on/off
- DAC + Pre-amp application
- Pure DAC apptication
RM599.00
- Headphone amp Preamplifier application
- HiRes Audio
- Ultra High performance NFCA Modules
- 3 Level Gain Setting
RM599.00
- Material: single strand silver plated wire plus oxygen-free copper wire
- Wire Category: RCA Interconnect Cable
- Colour classification: red + black
- Connector: Gold plating
- Length: 0.25 meters
RM159.00
- Wire using SGP-222
- Conductor resistance: 26.9Ω/KM
- Square number: 0.533MM²*2/19AWG*2
- OD: 8MM
RM319.00
- Wire using SGP-222
- Conductor resistance: 26.9Ω/KM
- Square number: 0.533MM²*2/19AWG*2
- OD: 8MM
RM199.00
- Wire using SGP-222
- Wire inner core: 8*0.16MM 6N single crystal copper silver-plated wires + 180*0.08MM 6N single crystal copper
- Conductor resistance: 26.9Ω/KM
- Square number: 0.533MM2*2/19AWG*2
- OD: 8MM
RM159.00
- Wire using SGP-222
- Wire inner core: 8*0.16MM 6N single crystal copper silver-plated wires + 180*0.08MM 6N single crystal copper
- Conductor resistance: 26.9Ω/KM
- Square number: 0.533MM2*2/19AWG*2
- OD: 8MM
RM319.00
- Headphone amp and pre-amp
- 4-pin XLR, 4.4 balanced, and 6.35mm outputs
- 3-step gain switch
- Can drive full-sized headphones and sensitive IEMs
- NFCA modules
- THD+N: <0.00006%
- DNR: 145dB
- Noise: <0.2uVrms
- Output impedance: <0.1Ω
- Maximum output power: 7600mW x2
RM2,199.00
- Bluetooth 5.0 LDAC transmission :DX3Pro+ has the certification of Hi-Res Audio Wireless and LDAC. It uses newest QCC5125 chipset to support LDAC/AAC/SBC/APTX/APTX LL/APTX HD protocol. To get even better sound quality from Bluetooth, we abandon the built-in DAC of QCC5125 and connect its digital signal to ES9038Q2M to decode.
- NFCA circuit :The new DX3 Pro+ has the NFCA circuit optimized for this unit, giving the ultra low noise and distortion. It pairs with high sensitivity IEMs and power hungry high impedance headphones nicely.
- Pre-amplifier function :Adapt to different usage scenarios, DX3 Pro+ has 4 output modes: Headphone Amp, Headphone Amp+ Line out, DAC, and Pre amplifier.
- PA3s is the best power amplifier for DX3 Pro+: PA3s has RCA+TRS balanced inputs. When used with DX3 Pro+, the TRS balanced input can be used to input other audio sources. The output power of 80W x 2@4Ω, 10%THD+N, 65W X 2@4Ω, 1%THD+N can be adapted to most situations where speakers are used.
- Bluetooth headphone amp / Bluetooth DAC application: Connect the Bluetooth of the phone, tablet or notebook to DX3 Pro+, and connect the power amplifier, active speakers or headphones to the DX3 Pro+'s output, then DX3 Pro+ becomes your Bluetooth Headphone amp / Bluetooth DAC. If your device supports LDAC transmission, you will get even better experience.
RM799.00
- Comfort zone with lowest distortion :The lowest THD+N of PA3s is in the range of 10-20W output, which happens to be the power range commonly used for listening to music. Everything is just in the right condition.
- With the help of a DAC, the function is expanded to a greater extent :PA3s can be used with a DAC to expand the categories of digital inputs; if used with a DAC+HPA, more comprehen sive functions can be achieved.
- Balanced + Single- ended inputs :PA3s provides TRS balanced input and RCA single: end- ed input. The u use of balanced input eliminates potential ground loop problems giving the pristinely clean audio without any hum.
- High output power :PA3s could output 80W x2 at 4ohm load, 10% THD+N. In higher standard of THD+N of 1%,output power will be 65W x2 at 4ohm load. The output power is enough to drive any bookshelf speakers and even some floor speakers.
- 2xMA12070 Fully balanced Class D amplifier :Each channel of PA3s uses one MA12070 Class D power amplifier chip. This allows separation in layout improving performance and reducing crosstalk. The power is shared across two chips, the heat dissipation is also halved for each chip, improving reliability and extending the lifespan of the product.
RM599.00